LayerUp Stats 5

Add Sep 1, 26 Sync Sep 3, 26

Table Talk

Nothing here yet. Love this design? Say so - the designer might see it.

Phase 10 Scorecard Case

for Phase 10 (1982) Layer by Layer

Eric

Storage & Containers Free

View on MakerWorld 27 81 Added Mar 12, 26 | Updated Sep 2, 26 Support Eric by Liking and Boosting their model.

Plan Your Print

About 185 g of filament From the designer's print profile

Print Profile (3) A1 - 0.2mm layer, 2 walls, 5% infill 6h 16m 190 g PLA

A1 - 0.2mm layer, 2 walls, 5% infill

3 plates 6h 16m 190 g PLA

A1, X1, H2D, P1P, X1E, P1S, X1 Carbon, H2C, H2S, H2D Pro, P2S, X2D, A2L

Low infill to save filament, on 3 plates to support any printer size.

Plate Details (3)

0.4 mm nozzle, all plates

Plate 1

3h 9m 97 g PLA · 2 g PLA · 95 g

Plate 2

2h 55m 92 g PLA · 3 g PLA · 89 g

Plate 3

11m 1 g PLA · 1 g

H2D - 0.2mm layer, 2 walls, 5% infill

2 plates 5h 32m 185 g PLA

H2D, H2S, H2C, H2D Pro

Low infill for reduced filament cost. Can be increased for more strength if desired.

Plate Details (2)

0.4 mm nozzle, all plates

Plate 1

5h 24m 184 g PLA · 2 g PLA · 182 g

Plate 2

9m 1 g PLA · 1 g

Single Color A1 - 0.2mm layer, 2 walls, 5% infill

3 plates 6h 12m 189 g PLA

A1, X1 Carbon, X1, P2S, H2D, H2C, P1S, H2S, P1P, A1 mini, X1E, H2D Pro, X2D, A2L

This model is a single-color print; the text is inset into the part.

Plate Details (3)

0.4 mm nozzle, all plates

Plate 1

3h 6m 96 g PLA · 96 g

Plate 2

2h 55m 92 g PLA · 92 g

Plate 3

11m 1 g PLA · 1 g

As sliced by the designer. Your printer, filament, and settings may change these numbers.

Designer's Description

A phase 10 case that includes both phase tracking and a scorecard for up to 6 players. It holds one deck split in half; both sides are equally deep as there is no “up” orientation, so to prevent cards spilling out the cards can fully fit in either side.

Each player needs 3 pegs minimum, one for the tracker, one for the 10s score tracking and one for the 100s score tracking. An example of scoring can be seen at the bottom of the page or in the listed pictures.

There are spots for 10mm x 3mm magnets to allow for a solid latch, these are not necessary but prevent accidental spills.

The hinge is a tight fit, but it is flexible, when putting both parts together make sure to press in the middle of the rod to help it snap in. The hinge makes noise when opening and closing, I recommend sanding both portions of the hinge before assembling to help prevent this noise.

Folded up it is approximately 6in x 5in x 2in.

Boost Me

(note the 10,20,30… are there for general reference, the left is 5s the right is 10s)

phase 10 phase 10 box phase 10 card box card game