Table Talk
Nothing here yet. Love this design? Say so - the designer might see it.

Three-in-one chess and Gomoku & storage board / chess & chessboard box

Translated from Chinese · 三合一象棋和五子棋&收纳棋盘 / chess&xiangqi&chessboard box
Plan Your Print
About 129 g of filament
Print Profile (3) 棋子&一体棋盘 / Chess pieces & integrated chessboard 4h 50m 129 g PLA
棋子&一体棋盘 / Chess pieces & integrated chessboard
2 plates 4h 50m 129 g PLA
A1 mini, P1P, H2D, X1, X1E, X1 Carbon, A1, P1S, H2D Pro, H2S, P2S, H2C, X2D, A2L, H3C
无需支撑,棋盘一体打印,打印后轻轻向盒内面折叠棋盘,铰链即可活动。 No support is required. The chessboard is printed integrally. After printing, gently fold the chessboard towards the inner surface of the box, and the hinge will be movable.
Plate Details (2)
0.4 mm nozzle, all plates
Plate 1
3h 13m 100 g PLA · 89 g PLA · 11 g
Plate 2
1h 37m 29 g PLA · 25 g PLA · 2 g PLA · 2 g
分体棋盘 / detachable chessboard
2 plates 3h 32m 103 g PLA
A1 mini, P1P, X1, H2D, P1S, X1 Carbon, A1, X1E, H2D Pro, H2S, P2S, H2C, X2D, A2L, H3C
分体棋盘,打印后需两根耗材丝穿入连接铰链 Separate chessboard. After printing, two filaments of consumables need to be threaded through to connect the hinges.
Plate Details (2)
0.4 mm nozzle, all plates
Plate 1 · 分体一
2h 59m 94 g PLA · 83 g PLA · 11 g
Plate 2 · 分体二
33m 9 g PLA · 7 g PLA · 2 g
五子棋
1 plate 58m 24 g PLA
A1 mini, A1
逐渐打印,一盘搞定。 Print gradually and finish it in one go.
Plate Details (1)
0.4 mm nozzle, all plates
Plate 1
58m 24 g PLA · 12 g PLA · 12 g
As sliced by the designer. Your printer, filament, and settings may change these numbers.
Designer's Description

为我助力 如果你喜欢请为我助力,谢谢!If you like it, please give me a hand. Thank you!

简介:

这是一个迷你的三合一象棋和五子棋,铰链收纳棋盘, 迷你省时省料,无需支持,棋盘一体打印 (当然棋盘也有分体打印后用耗材组装的配置),模型尺寸对A1mini友好(因为我手头只有mini😊)。

说明:

棋盘:

1、双铰链设计:展开后可平整的作为棋盘使用,外面是国际象棋棋盘,里面是中国象棋棋盘;

2、折叠收纳盒:折叠后可收纳棋子成为一个棋盒,由卡扣来锁住,盒外有纹理便于打开;

3、有一体打印棋盘和分体打印棋盘配置:一体打印棋盘无需其他操作打完即可使用,分体棋盘铰链处留有2mm孔洞,在此孔洞中穿入一根176cm的耗材即可。

棋子:

1、双面设计:一面中国象棋一面国际象棋;

2、象棋图案:非红黑色棋面同字或同图案直接换色红黑棋子文字或图案均不同设计;

中国象棋字面,参照 《中国象棋竞赛规则》中红黑棋子的规范文字设计;

国际象棋图案,参照电子棋盘、在线对弈等国际大型平台规范(如 Chess.com 等)图符做的平面设计。

3、五子棋:按棋盘大小设计

打印建议:

耗材PLA/PETG等不限,PLA以外材料打印前一定烘干;

切片时必须墙 生成器必须选 Arachne ;

A1mini打印平台面积限制,棋盘切片时必须取消擦料塔;

建议红黑子一盘打印反而省时省料;

没有精准调校过自己打印机的, 建议开0.05-0.1的象脚补偿 避免打印成品铰链粘连;

如果你对你热床长期不清理维护,那么 建议打印棋子时打印板涂胶 。

不可以缩小打印 ,否则图案显示不全,棋盘盒强度不够。

Introduction:
This is a mini three-in-one chess set combining chess and gomoku. It features a hinged storage board, which is mini - sized, time - saving, and material-saving. It doesn't require additional support, and the board can be printed as a single piece (of course, there is also a configuration where the board is printed in parts and then assembled with consumables). The model size is friendly to A1mini (because I only have the mini version at hand 😊).

Instructions:
The Board:

  • Double - hinge design: When unfolded, it can be used flat as a chessboard. The outer side is a chessboard for Western chess, and the inner side is a chessboard for Chinese chess.
  • Foldable storage box: When folded, it can store chess pieces and become a chess box. It is locked by a buckle, and the outside of the box has a texture for easy opening.
  • There are configurations of one-piece printed board and split-piece printed board: The one-piece printed board can be used directly after printing without any other operations. For the split-piece printed board, there are 2mm holes at the hinge positions. You just need to thread a 176 - cm - long consumable through these holes. Chess Pieces:
  • Double-sided Design: One side is Chinese chess, and the other side is chess.
  • Chess Patterns: For non-red and black chess pieces, the same characters or patterns are not simply recolored. The characters or patterns of red and black chess pieces are designed differently.
  • For the Chinese chess characters, they are designed referring to the standard characters of red and black chess pieces in the "Rules of Chinese Chess Competitions".
  • For the chess patterns, they are designed as graphic designs referring to the standards of international large platforms such as electronic chessboards and online games (e.g., Chess.com ).
  • Gobang Pieces: Designed according to the size of the chessboard.

Printing Suggestions:
Consumables such as PLA/PETG are acceptable. Materials other than PLA must be dried before printing.
When slicing, the wall generator must be selected as Arachne.
Due to the limited area of the A1mini printing platform, the wipe - tower must be disabled when slicing the chessboard.
It is recommended to print the red and black chess pieces in one plate, which saves time and materials.
For those who haven't precisely adjusted their printers, it is recommended to set an elephant's foot compensation of 0.05 - 0.1 to avoid the adhesion of the printed hinge.
If you haven't cleaned and maintained your heated bed for a long time, it is recommended to apply glue to the printing plate when printing chess pieces.
Do not print in a reduced size, otherwise the patterns will not be fully displayed, and the strength of the chessboard box will be insufficient.

Translated from Chinese - show original

为我助力 如果你喜欢请为我助力,谢谢!If you like it, please give me a hand. Thank you!

简介:

这是一个迷你的三合一象棋和五子棋,铰链收纳棋盘, 迷你省时省料,无需支持,棋盘一体打印 (当然棋盘也有分体打印后用耗材组装的配置),模型尺寸对A1mini友好(因为我手头只有mini😊)。

说明:

棋盘:

1、双铰链设计:展开后可平整的作为棋盘使用,外面是国际象棋棋盘,里面是中国象棋棋盘;

2、折叠收纳盒:折叠后可收纳棋子成为一个棋盒,由卡扣来锁住,盒外有纹理便于打开;

3、有一体打印棋盘和分体打印棋盘配置:一体打印棋盘无需其他操作打完即可使用,分体棋盘铰链处留有2mm孔洞,在此孔洞中穿入一根176cm的耗材即可。

棋子:

1、双面设计:一面中国象棋一面国际象棋;

2、象棋图案:非红黑色棋面同字或同图案直接换色红黑棋子文字或图案均不同设计;

中国象棋字面,参照 《中国象棋竞赛规则》中红黑棋子的规范文字设计;

国际象棋图案,参照电子棋盘、在线对弈等国际大型平台规范(如 Chess.com 等)图符做的平面设计。

3、五子棋:按棋盘大小设计

打印建议:

耗材PLA/PETG等不限,PLA以外材料打印前一定烘干;

切片时必须墙 生成器必须选 Arachne ;

A1mini打印平台面积限制,棋盘切片时必须取消擦料塔;

建议红黑子一盘打印反而省时省料;

没有精准调校过自己打印机的, 建议开0.05-0.1的象脚补偿 避免打印成品铰链粘连;

如果你对你热床长期不清理维护,那么 建议打印棋子时打印板涂胶 。

不可以缩小打印 ,否则图案显示不全,棋盘盒强度不够。

Introduction:
This is a mini three-in-one chess set combining chess and gomoku. It features a hinged storage board, which is mini - sized, time - saving, and material-saving. It doesn't require additional support, and the board can be printed as a single piece (of course, there is also a configuration where the board is printed in parts and then assembled with consumables). The model size is friendly to A1mini (because I only have the mini version at hand 😊).

Instructions:
The Board:

  • Double - hinge design: When unfolded, it can be used flat as a chessboard. The outer side is a chessboard for Western chess, and the inner side is a chessboard for Chinese chess.
  • Foldable storage box: When folded, it can store chess pieces and become a chess box. It is locked by a buckle, and the outside of the box has a texture for easy opening.
  • There are configurations of one-piece printed board and split-piece printed board: The one-piece printed board can be used directly after printing without any other operations. For the split-piece printed board, there are 2mm holes at the hinge positions. You just need to thread a 176 - cm - long consumable through these holes. Chess Pieces:
  • Double-sided Design: One side is Chinese chess, and the other side is chess.
  • Chess Patterns: For non-red and black chess pieces, the same characters or patterns are not simply recolored. The characters or patterns of red and black chess pieces are designed differently.
  • For the Chinese chess characters, they are designed referring to the standard characters of red and black chess pieces in the "Rules of Chinese Chess Competitions".
  • For the chess patterns, they are designed as graphic designs referring to the standards of international large platforms such as electronic chessboards and online games (e.g., Chess.com ).
  • Gobang Pieces: Designed according to the size of the chessboard.

Printing Suggestions:
Consumables such as PLA/PETG are acceptable. Materials other than PLA must be dried before printing.
When slicing, the wall generator must be selected as Arachne.
Due to the limited area of the A1mini printing platform, the wipe - tower must be disabled when slicing the chessboard.
It is recommended to print the red and black chess pieces in one plate, which saves time and materials.
For those who haven't precisely adjusted their printers, it is recommended to set an elephant's foot compensation of 0.05 - 0.1 to avoid the adhesion of the printed hinge.
If you haven't cleaned and maintained your heated bed for a long time, it is recommended to apply glue to the printing plate when printing chess pieces.
Do not print in a reduced size, otherwise the patterns will not be fully displayed, and the strength of the chessboard box will be insufficient.

chess 象棋 国际象棋 中国象棋 棋盘 收纳盒
Xiangqi box art Xiangqi 762 Lift the Lid
Cover Colors

Main colors from the cover art. Find matching filament, or tap swatches to narrow.

Matching filament