Table Talk
Nothing here yet. Love this design? Say so - the designer might see it.

Light Dorfromantik Tile Holders with connectors

Plan Your Print
About 10 g of filament
Print Profile (2) SINGLE, 0.2mm layer, 2 walls, 15% infill 34m 10 g PLA
SINGLE, 0.2mm layer, 2 walls, 15% infill
1 plate 34m 10 g PLA
P1S, H2C, H2D Pro, P1P, X1, A1, X1E, X1 Carbon, H2S, P2S, X2D, A2L, H2D, H3C
SINGLE version - has noses on one side and holes on other side - easy to print, easy to connect, easy to disconnect, stable on table, not movable
Plate Details (1)
0.4 mm nozzle, all plates
Plate 1 · SINGLE
34m 10 g PLA · 10 g
DOUBLE, 0.2mm layer, 2 walls, 15% infill
1 plate 35m 10 g PLA
P1S, H2D Pro, H2S, P2S, X1 Carbon, P1P, H2D, X1E, A1, H2C, X2D, X1, A2L, H3C
DOUBLE version - has noses and holes on all sides - easy to print, slightly difficult to connect, hard to disconnect, stable on table, stable while moving around
Plate Details (1)
0.4 mm nozzle, all plates
Plate 1 · DOUBLE
35m 10 g PLA · 10 g
As sliced by the designer. Your printer, filament, and settings may change these numbers.
Designer's Description

Playing Dorfromantik with children is not easy as it very likely happens that the tiles are easily be moved once the world gets bigger and they have to “climb” over the table. I was looking for a solution here but most of them were to “heavy”, which means they need lots of filament and do not fit into the box at all. I found this very cool ultralight version (https://makerworld.com/en/models/986394-ultralight-dorfromantik-board-game-tile-holders) but they do not stick to each other, so the same problem appears.

So I created my own version from scratch (FreeCAD file is included).

Specs:

  • Very light - one grid (containing 16 tiles) weights only about 10 g
  • Only 2 mm height (tried a 1 mm version, but it's too fragile)
  • Stable base
  • Loose fit (tiles go in and out easily)
  • Angled noses for easy connection and good stability during gameplay
  • Bridges start 0.2 mm higher to avoid need for support (they are only 6 mm wide, so no problem to print)
  • Optimized for 0.2 mm standard print profiles - no change of settings needed (hopefully working on any printer with any filament)

I first created a version with nose and hole on all sides (DOUBLE). They connect very well and are very stable. I recommend using this version if you want to connect them and leave them connected forever. (I was surprised about the strength of a 0.6 mm plastic nose - see picture)

Since I want to disconnect them again easily, I also created the SINGLE version, where every edge has only one nose/hole. This is much easier to assemble and disassemble, but you cannot store / transport it in connected state.

If you want you can try the double version and if you later decide to switch to single version you don't need to reprint all the grids again, you can just cut off some of the noses of the double version and then single and double will fit together.

Hope you have fun with this version. If you have any suggestions please leave a comment.

dorf romantik
Dorfromantik: The Board Game box art Dorfromantik: The Board Game 2022 Lift the Lid
Cover Colors

Main colors from the cover art. Find matching filament, or tap swatches to narrow.

Matching filament