LayerUp Stats 26

Add Jul 30, 26 Sync Aug 16, 26

Table Talk

Nothing here yet. Love this design? Say so - the designer might see it.

Explorers of Navoria Base+Exp +3D Resources Trays

for Explorers of Navoria (2024) Layer by Layer

Licotto

Tokens & Resources Free

View on MakerWorld 5 7 Added Jun 5, 26 | Updated Aug 15, 26 Support Licotto by Liking and Boosting their model.

Also Found On Printables 2

Plan Your Print

About 683 g of filament From the designer's print profile

Print Profile (3) 0.2mm layer, 2 walls, 15% infill 19h 15m 683 g PLA

0.2mm layer, 2 walls, 15% infill

9 plates 19h 15m 683 g PLA

P1S, P1P, X1, X1 Carbon, X1E

Plate Details (9)

0.4 mm nozzle, all plates

Plate 1 · Tiles

2h 47m 135 g PLA · 135 g

Plate 2 · Teal & Purple Players

2h 29m 77 g PLA · 39 g PLA · 38 g

Plate 3 · Yellow & Black Players

2h 38m 76 g PLA · 38 g PLA · 38 g

Plate 4 · White Player, Contracts, & SOLO

1h 57m 61 g PLA · 61 g

Plate 5 · Apples & Crystals

2h 23m 91 g PLA · 46 g PLA · 45 g

Plate 6 · Swords & Cards (Gray)

1h 49m 59 g PLA · 59 g

Plate 7 · Cards -Blue & Orange

58m 34 g PLA · 17 g PLA · 17 g

Plate 8 · Cards -Yellow, Green, Magenta

1h 27m 52 g PLA · 18 g PLA · 17 g PLA · 17 g

Plate 9 · Cards -all white

2h 46m 98 g PLA · 98 g

0.2mm layer, 2 walls, 15% infill

1 plate 13m 4 g PLA

A1, P1S, X1, A1 mini, H2S, X2D, H2D Pro, P1P, A2L, X1E, X1 Carbon, H2C, P2S, H2D

This is a TEST PRINT to see if your Sleeved Cards will fit in the card trays that I included in my Remix of the Navoria insert. It will print in about 10 minutes and is only a 2.5g print. It is the trimmed part of the frame for the card trays. If your sleeves don't fit, please message me or leave a comment so I can try to help. I would need to know the size of the sleeve you are using (in millimeters). Thank you! …and remember, if this helps, don't forget to Boost me or give it a Like and stuff :D Inside measurements are now 66mm x 89mm.

Plate Details (1)

0.4 mm nozzle, all plates

Plate 1 · TEST PRINT for Sleeves

13m 4 g PLA · 4 g

Card Trays for SLEEVED Cards -choice of colors or all-white

3 plates 5h 57m 201 g PLA

A1, A2L

The inside measurements of these trays are 66mm x 89mm. If you use the “TEST” Print Profile, you can easily see if you sleeves will fit in the trays without wasting extra filament.

Plate Details (3)

0.4 mm nozzle, all plates

Plate 1 · Cards -Blue, Gray, Orange

1h 31m 51 g PLA · 17 g PLA · 17 g PLA · 17 g

Plate 2 · Cards -Yellow, Green, Magenta

1h 32m 51 g PLA · 17 g PLA · 17 g PLA · 17 g

Plate 3 · Cards -all white

2h 55m 99 g PLA · 99 g

As sliced by the designer. Your printer, filament, and settings may change these numbers.

Designer's Description

I put together a bit of a Franskenstein insert for Navoria! I wanted an insert that wouldn't let pieces fall all over because I always have to take my games elsewhere to play, so they're going to go vertical and upside down and moved a lot. Not only did I take bits from the three different models below to add to this, but I also modified the tile trays a bit since the finger slots were VERY small and I could barely fit my pinky in it. I slightly increased the two top tile trays a bit as they were quite tight on the tiles. Then I added simple holes to be able to reach under the stacks to easily get the entire stack.

These are the following substitutions I used in the insert:

Modified version of Player & Resource Trays from @DavidBennett_493940
https://www.printables.com/model/1136698-insert-for-explorers-of-navoria
I love his original trays, but just like I didn't prefer the trays from this insert, I don't want to spend time placing pieces in exact locations after a game -just pouring them into a bin is so much quicker. And I really liked the design DavidBennett did on these, so I just gutted them and make them simple.

Modified version of Stackable Card Box from IKeiran
https://makerworld.com/en/models/1375329-stackable-card-box
These make it SO nice to just take out to place on the table/playmat, but my favorite thing is how the stack so easily and don't move in the box.

My version of this insert used the custom Navoria resources from julienJ3D
https://makerworld.com/en/models/1382592-navoria-resources
I didn't modify these at all (other than I made my swords gray rather than brown -just preference.

I hope you enjoy this version. I love the colors I found and think it all looks fantastic.