Table Talk
Nothing here yet. Love this design? Say so - the designer might see it.
Log in to join the conversation.
Trinket Trove Organizer
Inserts
Free
Plan Your Print
Sign in
to track this print from Want to Printed.
✓ Fits sleeved cards
✓ Fits premium sleeves
About 116 g of filament
Print Profile (2) 0.2mm layer, 2 walls, 10% infill 4h 14m 116 g PLA
0.2mm layer, 2 walls, 10% infill
2 plates
4h 14m
116 g PLA
A1, H2D, H2C, P2S, H2S, X1E, X1 Carbon, P1P, X2D, X1, H2D Pro, A2L, P1S
Plate Details (2)
0.4 mm nozzle, all plates
Plate 1 · card tray
3h 2m
90 g
PLA · 90 g
Plate 2 · player tile tray
1h 13m
26 g
PLA · 26 g
Hinged Lid + Drop-Down Front Door (Print-in-Place)
1 plate
3h 12m
95 g PLA
A1, H2S, P1S, X1 Carbon, X1E, H2D, A2L, H2D Pro, X1, P2S, X2D, P1P, H2C
## Profile description
This profile adds a drop-down front door to each card tray, so you can slide cards out without lifting them over the front wall.
What's different from the original profile
## Print settings
• Printer: tested on Bambu Lab A1 with PLA and a 0.4 mm nozzle.
• Layer height: 0.2 mm.
• Supports: none. The door is already oriented open and flat on the bed.
• Wall loops: 3 or more.
• Infill: 15%.
• Brim: off. Do not add a brim around the door hinge, or it may fuse the door to the tray.
• Elephant foot compensation: keep it on (default). The hinge clearance near the bed is 0.35 mm.
Plate Details (1)
0.4 mm nozzle, all plates
Plate 1 · card-tray-open
3h 12m
95 g
PLA · 95 g
As sliced by the designer. Your printer, filament, and settings may change these numbers.
Designer's Description
Title
trinket trove organizer
A snug-fit organizer for the Trinket Trove base box (140×140×48 mm). Two hinged-lid trays for sleeved cards plus an upright tile holder, all printable without supports.
Description
Designed to fit inside the Trinket Trove base box, with room for the rulebook on top. Cards and tiles are split up so setup and cleanup take seconds.
Card trays ×2 (hinged lids)
- Each tray holds one stack of sleeved cards. It was designed with 0.08 mm matte sleeves, which measure 65×90 mm; one stack is about 35 mm tall.
- The lid opens about 200° on a snap-in hinge and clicks shut with side bumps.
- The floor rises toward the front so cards don't slide out.
- A U-shaped front cutout and a floor finger slot make it easy to grab cards.
- The lids have a mouse cut-out and star details, and the back of each tray has a rat-and-terrain decoration.
Tile holder ×1
- Stores the 8 player tiles (47×58 mm) and the start/end tiles (80×20 mm) upright.
Compatibility
- Base game only.
- Cards: sized for 0.08 mm matte sleeves. Thicker sleeves may not fit.
- Promo tiles are not supported. There is no space for them.
Print Settings
- Tested on: Bambu Lab A1, PLA
- Nozzle: 0.4 mm
- Layer height: 0.2 mm
- Supports: none needed
- Wall loops: 3 or more recommended. The walls are only 1.2–1.5 mm thick, so they are mostly perimeters.
- Infill: 15%
- Brim: optional. The trays are tall, so add one if bed adhesion is weak.
Assembly
- Line up the hinge clips at the back of the lid with the dome pins at the back of the tray.
- Press until it snaps in. The slots beside the hinge let it flex slightly.
- Close the lid and check that the side bumps click into place.
